How the Scratch Custom Upper and Lower case blocks work

Last week I wrote a post about the custom string handling blocks I have written for Scratch. These have been very well received and I have had quite a few positive tweets back about them. I’m glad people are finding them useful!

Two of the blocks I have written allow you to convert a string to either upper or lower case. Now Scratch 2 when dealing with strings or characters is case insensitive, by this I mean if you perform a comparison of A = a Scratch will evaluate these to be the same. To clarify this, lets look at the block of code below.

Character ComparisonIf you run this block, you will see that the variable result is set to 1. This is what I mean when I say case insensitive, we may consider that A is not the same as a. So what does this have to do with converting our string to upper or lower case? Well, I’ll cover this a little later and you will see how this case insensitivity can help us!


If I was asked to write a very basic case changing method (same as a block in Scratch) in say C# (which is my preferred language), I may well consider looking at ASCII codes for characters, this is ignoring the fact that there is already two methods available in the .NET Framework to convert between upper and lower case!!. What is ASCII? well, I’m not going into the depths of explaining this here, but if you look at the Wikipedia entry for it at this will give you a full overview of it. ASCII codes can be our friend here for converting between case, if you consider the ASCII code for A is 65 (decimal) and the ASCII code for a is 97 (decimal), you can see there is a difference in the code values of 32. This works for B/b and C/c, etc.

So a method to convert upper case to lower case could loop over all the characters in a string and check the ASCII value for it. If the value is between 65 and  90, (A to Z), we can consider it to be an upper case letter, if we then add 32 to the ASCII value, this will give us the lower case version. We want to range check the letter value to ensure we are working with an upper case letter, otherwise the resulting string would look a little strange.

The small C# method below is something that will convert upper to lower case. Now at this point any C# programmer looking at the method would probably pick it to pieces and to be honest I can too. If I was going to write a version for production code it would be vastly different to this. This method has been written to explain my points above and nothing more.

string ToLowerCase(string str)
    string result = String.Empty;

    for (int loop = 0; loop < str.Length; loop++)
        if ((int)str[loop] >= 65 && (int)str[loop] <= 90)
            result += Convert.ToChar((int)str[loop] + 32);
            result += str[loop];

    return result;

Passing the string abcd&ABCD to this method would return the string abcd&abcd. Great! we have a working conversion routine. So lets go and implement this in Scratch.

Our Scratch Version

Right, so now we know we can work with the ASCII codes for letters, we just convert what we have above to the corresponding Scratch code, right? …. Well, no we don’t sadly. Scratch does not give us the ability to work with the ASCII codes for letters, so this method will not work. Great! so how can we do this then? Well, remember I explained at the beginning of this post that Scratch is case insensitive and it can be our friend, well this is where it becomes our best friend!

When I was implementing my string blocks, I really did think that case conversion had to be included, so with a little thought figured there must be a way of doing this. The trick with solving any problem like this is to have a look at what we have to work with in Scratch. Whilst the C# method is very nice, we have to throw most of it away and think again. My eureka moment came when I thought about lists. My thinking here when converting to lower case was as follows:

1. Have a list that contains all the lower case letters a through to z
2. Loop through every character in our string and see if it exists in our list
3. If it exists, use the character found in the list (which will be the lower case character)
4. If it is not found in the list, use the original character.

So, putting this together, I generated a list called LowerCase which looks like this:

Lowercase ListThis method will work even if we pass over lowercase letters, we will still get our character from the list, which will be lower case. So, my Scratch ToLowerCase block looks like this:

ToLowerCase BlockOur block starts by initialising a couple of variables. result will hold our converted string and charCount is used by the repeat block to loop through every character in our string. I have then implemented another custom block called GetLowerCaseLetter. Splitting out code like this into another block makes the code more readable and also gives us yet another block that allows us to do single character conversion. Our GetLowerCaseLetter block looks in our list and finds the lower case letter we need. After calling this block, our lower case letter is held in the variable letterResult so we simply add this to our result variable. We then add 1 to the character count and go around the loop again. This keeps going until we have worked with every character in our string.

The GetLowerCaseLetter Block

This is where most of the work is done. Lets have a look at this block.

GetLowerCaseLetter BlockAgain at the beginning we initialist a couple of variables. loop is used to loop through our LowerCase list. letterResult is used to return our converted character. We are then going to loop through the list a maximum of 26 times (remember a to z!!). When we are in the loop, we check if the letter we have passed to the block, e.g. A is in our list. So using a simple if block we are essentially saying if A = a then set letterResult to the item found in our list, which will be a. As we don’t want to go around the loop again, we stop this script. At this point letterResult holds a which is the lower case version of what we passed in. If we had passed in a it would have found this and letterResult would hold a.

If our block has got as far as the end of the loop, we have another if block that says if letterResult is empty, we must have passed in a character other than a letter of the alphabet, so just simply return it. This ensures anything like %&*() is still kept in the converted string.

So putting this to the test, if we use the block like this:

Call ToLowerCaseThe string we will get back is abcd&abcd, which is the lower case version of what we passed in!

Converting to Upper Case

Converting to upper case is exactly the same, we just use a list that contains upper case A to Z. If you look at the ToUpperCase block in the Scratch project, you will see it is exactly the same as its lower case version. The GetUpperCaseLetter block again is exactly the same as its lower case version.

So, again as you can see, whilst our Scratch version of converting to upper and lower case is very different to what we may do in other programming languages, if you sit back and think about the problem and consider what you have to work with in Scratch, there is generally always a way of implementing what you want to do.